Graco TurboBooster 2.0 Highback Booster

$69.99

Price on Amazon.com as of 2026-11-02 21:52 UTC, and subject to change.

A 2-in-1 booster seat with 2 modes: high-back booster 40 to 100 lb, 43 to 57 in; backless booster 40 to 100 lb, 43 to 57 in.

At a glance

  • Fits children from 40 to 100 lb
  • Up to 57 in tall
  • 2 modes: high-back booster, backless booster
  • Seat weighs 9 lb
  • 16.73 in wide
  • 10-year usable life
Check the current price

Opens Amazon.com in a new tab. As an Amazon Associate I earn from qualifying purchases.

CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON. THIS CONTENT IS PROVIDED ‘AS IS’ AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Specifications checked against Graco’s US site and manual on . Not hands-on tested. How I research

Who is the TurboBooster 2.0 Highback Booster for?

The Graco TurboBooster 2.0 Highback is a belt-positioning booster for children at least 4 years old, 40 to 100 lb and 43 to 57 inches tall. It uses the vehicle lap and shoulder belt only, converts to a backless booster with the same limits, has no LATCH, and expires 10 years after manufacture.

Reasons to consider it

  • Children at least 4 years old, 40 to 100 lb and 43 to 57 in, in both modes
  • A headrest with 6 height positions to place the shoulder belt guide
  • A backless mode with a belt positioning clip for a better shoulder belt fit
  • A 10-year useful life from the date of manufacture

Things to weigh up

  • No LATCH, so the booster must be buckled in even when no child is in it
  • Lap-only, motorized and door-mounted belts cannot be used with it
  • Not certified for aircraft use as a booster, because aircraft seats have no shoulder belts
  • In backless mode, the child's ears must be below the top of the vehicle seat back or headrest

My take on the TurboBooster 2.0 Highback Booster

This suits a family that wants a simple high-back booster that later becomes a backless one, and that has a lap and shoulder belt in the seating position. The trade-off is that nothing holds the booster in place except the belt, so it must stay buckled even when empty. Compared with the TurboBooster 2.0 LX Highback LATCH, it has no LATCH connectors and Graco lists it narrower (16.73 in against 19.84 in) and lighter (9 lb against 10.76 lb).

A research summary of Graco’s published specifications and manual, read . Not a hands-on test or a crash-safety rating.

Who the TurboBooster 2.0 Highback Booster fits

This seat covers 2 stages, and a child has to meet every limit of the stage they are in. Graco gives it a 10-year life from the date of manufacture, so check the date label before using a hand-me-down.

High-back booster40 to 100 lb · 43 to 57 in · from 4 years
The seat’s own back and belt guide route the vehicle belt across the shoulder, and the sides give the child something to lean on when they sleep.
Backless booster40 to 100 lb · 43 to 57 in · from 4 years
Only the base is left, so the vehicle seat has to support the child’s back and head, and the belt guide sits at the hip.

What are the TurboBooster 2.0 Highback Booster weight, height and age limits?

Graco TurboBooster 2.0 Highback Booster limits by mode
ModeChild weightChild heightMinimum ageConditions
High-back booster40 to 100 lb43 to 57 in4 yearsAt least 4 years old
Backless booster40 to 100 lb43 to 57 in4 yearsAt least 4 years old

A child must meet every limit for the mode they use. The labels on your seat and its manual are the final word.

TurboBooster 2.0 Highback Booster specifications

Seat weight
9 lb
Width
16.73 in
Depth
9.09 in
Height
29.39 in
Usable life
10 years
Aircraft use
Not published

How the TurboBooster 2.0 Highback Booster installs

Lower anchors
No LATCH. Check your vehicle manual for which seating positions have anchors, and switch to the seat belt once the child passes the anchor weight limit in the manual.

Every install is a fit between one seat and one vehicle. Read both manuals, and use a free inspection station if anything is unclear.

An empty car seat installed on a back seat, seen through an open car door

Will it fit your car?

At 16.73 in at its widest, this seat is one of the narrower ones in its class and is a candidate for three across in many mid-size cars. It weighs 9 lb, which matters if you will move it between cars or carry it through an airport.

  • Check your vehicle manual for lower anchor positions and any head-restraint rules.
  • Rear-facing seats need front-seat room: try the install behind the driver before you commit.
  • Aircraft certification is printed on the seat’s own label; check before you fly.

What features does the TurboBooster 2.0 Highback Booster have?

  • Converts high-back to backless
  • Open-loop belt guides
  • No LATCH

Colors listed in the US

Declan, Freya, Geo Pop, Lilac Mod, Hot Wheels Super Charged, Barbie Icon.

TurboBooster 2.0 Highback Booster colors and prices

4 colors are listed on Amazon right now. Prices differ by color, so compare before choosing. The fabric is the only difference between them; the shell, harness and limits are identical. Prices were retrieved Nov 2, 9:52 PM UTC and can change.

Compare TurboBooster 2.0 Highback Booster colors side by side
Compare colorsFreyaCheck priceDeclanCheck priceBarbieCheck priceHot WheelsCheck price
Price$69.99$69.99$79.99$79.99
AvailabilityIn stockIn stockIn stockIn stock
Price checkedNov 2, 9:52 PM UTCNov 2, 7:45 PM UTCNov 2, 7:45 PM UTCNov 2, 7:45 PM UTC

Prices and availability shown are accurate as of the time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply. As an Amazon Associate I earn from qualifying purchases.

What to know before you live with it

How it is held in the car

There is no LATCH and no separate installation step. The manual says to place the booster forward-facing in the back seat with its bottom as flat as possible, thread the shoulder belt through the guide on the headrest, and buckle the child in. The lap belt must go under both armrests and lie low across the hips and thighs, and the shoulder belt goes under the armrest on the buckle side. The front of the booster must not hang over the vehicle seat, and the vehicle seat headrest must not create a gap between the vehicle seat and the booster. Graco also says to keep it buckled when unoccupied, because a loose booster can injure occupants in a crash.

Source: Graco TurboBooster 2.0 manual (PDF)

Setting the headrest and checking belt fit

You raise or lower the headrest by squeezing the adjustment lever, then pull on it to check that it has locked into one of 6 height positions. The belt guides should sit even with or just above the shoulders, so the shoulder belt crosses the shoulder between the neck and the edge of the shoulder (the manual calls this the red zone). The belt must never go under the arm or behind the back, and it must lie flat, not twisted. If your child will not keep the belt in place, or slouches and slides down, the manual says not to use this booster and to use a different car seat.

Source: Graco TurboBooster 2.0 manual (PDF)

Using it as a backless booster

To convert it, you recline the back and lift it off the base. The backless booster still needs a lap and shoulder belt. In this mode the manual adds one check: the child's ears must be below the top of the vehicle seat back or headrest. If the shoulder belt falls outside the red zone, you must use the belt positioning clip. Its strap loops through a slot on the bottom of the base, and the clip slides onto the shoulder belt so that it sits right at the top of the shoulder.

Source: Graco TurboBooster 2.0 manual (PDF)

Armrests, cover and cleaning

On models that need assembly, the armrests clip into the base and are held at your chosen height with a screw. To move them, you remove the screw, press the button and reinsert the screw. The cover comes off by releasing elastic loops and hooks. Graco says to machine wash it in cold water on a delicate cycle, drip dry it and not use bleach. You can also spot clean with mild soap and cool water, and remove the head support cover if needed. The care tag on the pad has the full washing instructions.

Source: Graco TurboBooster 2.0 manual (PDF)

Is the TurboBooster 2.0 Highback Booster recalled?

  • 16C004000: does not cover this model. Campaign 16C-004 is defined by TurboBooster model numbers 1963973, 1963974, 1963975, 1963976, 1967886 and 1975173, built December 22, 2015 to April 5, 2016, whose instructions lacked a belting warning. This TurboBooster 2.0 Highback carries model numbers 2184597, 2227100 and 2227099, none of which is in that list. Campaign source (read ).

Each campaign naming this family was read against this model’s numbers and build dates, and none covers it. Still check your seat’s model number and date of manufacture before use, especially on a used seat.

NHTSA recall search · Recent car seat recalls

TurboBooster 2.0 Highback Booster: common questions

What are the TurboBooster 2.0 Highback weight and height limits?

Both modes are for children at least 4 years old who weigh 40 to 100 lb and are 43 to 57 in tall. The manual adds that a booster is no longer needed once the vehicle belt fits properly, typically around 4 ft 9 in and ages 8 to 12.

Graco TurboBooster 2.0 manual (PDF) (opens in a new tab)

Does the TurboBooster 2.0 Highback have LATCH?

No. This version uses only the vehicle lap and shoulder belt. Graco's TurboBooster 2.0 LX Highback LATCH is the sibling with front-adjust LATCH connectors.

Graco TurboBooster 2.0 Highback Booster product page (opens in a new tab)

Can the TurboBooster 2.0 be used on an airplane?

No. The manual says it is not certified for aircraft use as a booster, because aircraft seats do not have shoulder belts.

Graco TurboBooster 2.0 manual (PDF) (opens in a new tab)

When does the TurboBooster 2.0 expire?

Graco says to stop using it and throw it away 10 years after the date of manufacture. The date label is on the back of the seat. Graco also says to replace it after any crash.

Graco TurboBooster 2.0 manual (PDF) (opens in a new tab)

How wide and heavy is the TurboBooster 2.0 Highback?

Graco lists it at 16.73 in wide and 29.39 in tall, with a seat weight of 9 lb. That is narrower than the LX Highback LATCH (19.84 in) and the Stretch2Fit (19.69 in).

Graco TurboBooster 2.0 Highback Booster product page (opens in a new tab)

Can the TurboBooster 2.0 cover go in the washing machine?

Yes. The manual says to machine wash the cover in cold water on a delicate cycle and drip dry it, with no bleach.

Graco TurboBooster 2.0 manual (PDF) (opens in a new tab)

Answers refer to the model and manual version on this page. Check the instructions supplied with your seat.

Before you buy

  1. Weigh and measure your child. The limits above are the manufacturer’s, and a child has to meet all of them for the mode they will use.
  2. Confirm the exact version. Colors, retail exclusives and model numbers change limits more often than you would expect; Graco lists 6 colors of this seat.
  3. Read the manual before you buy, not after. It is linked above and holds the fit rules, the install methods and the expiry.
  4. Check recalls by model number and date of manufacture, and register the seat with Graco so you hear about the next one.

Sources

Other Graco booster seats

ModelTop child weightSeat weightWidthUsable life
TurboBooster 2.0 Highback Booster (this seat)100 lb9 lb16.73 in10 years
Tranzitions 3-in-1 Harness Booster100 lb14 lb19 in7 years
Nautilus 2.0 LX 3-in-1 Harness Booster Car Seat120 lb17.4 lb19.4 in10 years
Nautilus 2.0 3-in-1 Harness Booster Car Seat120 lb17.8 lb19.4 in10 years
TurboBooster 2.0 Backless Booster100 lb5.1 lb—10 years
TurboBooster 2.0 LX Highback Booster with LATCH System100 lb10.76 lb19.84 in10 years
TurboBooster 2.0 LX Highback Booster Seat featuring Safety Surround110 lb——10 years
TurboBooster LX Backless Booster with LATCH100 lb5.56 lb17.5 in10 years
TurboBooster Stretch2Fit Booster Seat110 lb11.73 lb19.69 in10 years